Parts For Harley-Davidson® Motorcycles

Approximately 3 Gallons.

Measures 12" W x 8.5" H. Available in three lengths; 23-3/4", 25-1/4", and 27". The tunnel depth is 6-1/4". The rear of the tank is 3.5" wide.

One piece, single cap design. Handcrafted from 14 and 16 gauge steel.

Requires the use of an L96-06 vented gas cap and 22mm petcock.

Required mount kits may be used on any custom application.

Note: Not for use on fuel-injected models. WARNING: All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems.

Zoom In

Approximately 4.25 gallons.

Fits 00-06 Softail Frames but requires the relocation of gauges, indicator lights and ignition switch.

Measures 21-1/4" L x 15-1/2" W x 7" H. The square tunnel width is 3.25" and the depth is 6". The rear of the tank is 4.5" wide.

One piece, single cap design. Handcrafted from 14 and 16 gauge steel.

Requires the use of an L96-06 vented gas cap and 22mm petcock. Required mount kits may be used on any custom application.

Requires the relocation of guages, indicator lights and ignition switch.

Note: Not for use on fuel-injected models. WARNING: All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems.

Zoom In

Approximately 3 Gallons.

Measures 28" L x 13-1/2" W x 7-3/4" H. The tunnel depth is 5-1/4". The rear of the tank is 3" wide.

One piece, single cap design.

Handcrafted from 14 and 16 gauge steel.

Requires the use of an L96-06 vented gas cap and 22mm petcock.

Required mount kits may be used on any custom application.

Note: Not for use on fuel-injected models.

WARNING: All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems.

Zoom In

2.5” direct bolt on tank for 01-07 carbureted softails.

One piece tank features a curved bottom for a custom look. Smooth top, made for use with no dash. Comes with filler bung. Approximately 5.5 gallon fuel capacity.

Dimensions are: 23-1/2" Long x 17-1/4" Wide x 9" High. Tunnel width is 3-1/4".

These tanks are powdercoated on the inside to ensure a clean sealed surface. There is no need to etch or use any other sealer. Minimal prep work will be needed prior to paint.

Requires the relocation of guages, indicator lights and ignition switch.

Requires stock seat modification or RWD seats are sold separately.

Made in the USA using 16 gauge stamped steel. Tig welded by an American craftsman.

Warning: all tanks are shipped unpainted. All gas tanks should be fitted before being painted to eliminate potential problems.

Zoom In

Approximately 4.6 gallons.

Fits most custom frames.

Measures 25" L x 13-1/2" W x 6.5" H. The tunnel depth is 6". The rear of the tank is 2.5" wide.

One piece, single cap design. Handcrafted from 14 and 16 gauge steel.

Requires the use of an L96-06 vented gas cap and 22mm petcock.

Required mount kits may be used on any custom application.

Note: Not for use on fuel-injected models. WARNING: All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems.

Zoom In

3" stretch direct bolt on tank for 08-10 fuel injected Road Glides, Electra Glides or Street Glides. 

One piece tanks feature a curved bottom for a custom look.  Available in 2 widths; 17.5" (approximately 6 gallon capacity), or 20" (approximately 6.5 gallon capacity).

Includes raw dash panel that replaces the existing dash.   Any aftermarket cap will fit.  We recommend drag specialties 0703-0060. Fuel-injected tank accepts the stock O.E.M. fuel-pump assembly and fuel level sending unit and uses a L96-07 vented gas cap. 

These tanks come powder-coated on the inside to ensure a clean sealed surface.  There is no need to etch or use any other sealer.  Minimal prep work will be needed prior to paint.

Requires stock seat modification. 

Seats are sold separately. Made in the

USA using 14 and 16 gauge steel.  Tig welded by an American craftsman.

Warning: all tanks are shipped unpainted. 

All gas tanks should be fitted before being painted to eliminate potential problems

Zoom In

2.5” direct bolt on tank for 01-07 softails.  One piece tank features a curved bottom for a custom look.   This tank uses the stock dash and accepts any aftermarket cap.  Comes with fuel gauge bung and filler bung. Approximately 5.5 gallon fuel capacity.   Dimensions are: 23-1/2" Long x 17-1/4" Wide x 9" High.  Tunnel width is 3-1/4".  We offer a low profile dash that fits this tank available in our online store at this link:

Low Profile Dash for RWD 2001-2007 Softail Tank

These tanks are powdercoated on the inside to ensure a clean sealed surface.  There is no need to etch or use any other sealer.  Minimal prep work will be needed prior to paint.

Requires stock seat modification.  Seats are sold separately.

Made in the USA using 16 gauge stamped steel.  Tig welded by an American craftsman.

Warning: all tanks are shipped unpainted.  All gas tanks should be fitted before being painted to eliminate potential problems.

Zoom In

3" stretch direct bolt on tank for 03-07 Fuel Injected, or 96-06 Carbureted Road Glides, Electra Glides or Street Glides, One piece tanks feature a curved bottom for a custom look. Available in 2 widths; 17.5" (approximately 6 gallon capacity), or 20" (approximately 6.5 gallon capacity). Includes raw dash panel that replaces the existing dash. Any aftermarket cap will fit. We recommend PN RWD-0703-0060.

Fuel-injected tank accepts the stock O.E.M. fuel-pump assembly and uses a L96-07 vented gas cap. Carbureted tanks include a filler plate/neck assembly and use a L96-07 vented gas cap.

These tanks come powder-coated on the inside to ensure a clean sealed surface. There is no need to etch or use any other sealer. Minimal prep work will be needed prior to paint.

Requires stock seat modification. Tanks fit with RWD Profile (PN RWD-0804-0247) and Protour (PN RWD-0804-0248) Seats, sold separately.

Note: Filler plate on carb tanks may require modifications to reinstall early-style sending unit.

Made in the USA using 14 and 16 guage steel. Tig welded by an American Craftsman.

Zoom In

3" stretch direct bolt on tank for 03-07 Fuel Injected, or 96-06 Carbureted Road Kings. One piece tanks feature a curved bottom for a custom look. Available in 2 widths; 17.5" (approximately 6 gallon capacity), or 20" (approximately 6.5 gallon capacity). Includes raw dash panel that replaces the existing dash. Any aftermarket cap will fit. We recommend PN RWD-0703-0060.

Fuel-injected tank accepts the stock O.E.M. fuel-pump assembly and uses a L96-07 vented gas cap. Carb tanks include a filler plate/neck assembly and use a L96-07 vented gas cap.

These tanks come powder-coated on the inside to ensure a clean sealed surface. There is no need to etch or use any other sealer. Minimal prep work will be needed prior to paint.

Requires stock seat modification. Tanks fit with RWD Profile (PN RWD-0804-0247) and Protour (PN RWD-0804-0248) Seats, sold separately.

Note: Filler plate on carb tanks may require modifications to reinstall early-style sending unit.

Made in the USA using 14 and 16 guage steel. Tig welded by an American Craftsman

Zoom In

Approximately 5 Gallons.

Measures 25"Lx 7" H. Available in two widths, 16" and 14".

The tunnel depth is 6-1/4". The tunnel width is 2.5".

WARNING: All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems.

Zoom In

Approximately 3 Gallons.

Measures 12" W x 8.5" H. Available in three lengths; 23-3/4", 25-1/4", and 27".The tunnel depth is 6-1/4".

WARNING: All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems.

Zoom In

Approximately 3 Gallons.

Measures 28" L x 13-1/2" W x 7-3/4" H. The tunnel depth is 5-1/4".

WARNING: All tanks are shipped unpainted. All gas tanks should be fitted, pressure-tested and sealed BEFORE being painted to eliminate potential problems

Zoom In

Frame Mount Kit includes:

2 Rubber Spacers (1-1/2"Wx5"Lx1/4"Thick)

2 Frame weld-on mounts (5-3/4"x1-1/4"; 7/8" holes)

4 Fuel tank mounting grommets

4 Inserts for rubber grommets

Zoom In

Recessed Mount Tank Hardware Kit includes:

1 Stock Filler Neck

1 Petcock (22 mm)

4 Tank Mount Cups

4 Threaded Insert Mounts

Zoom In

Standard Mount Tank Hardware Kit includes:

1 Stock Filler Neck

1 Petcock (22 mm)

4 Tank Mount Doublers

4 Threaded Insert Mounts

Zoom In